How To Setup A Standee (Roll Up Banner)

How To Setup A Standee (Roll Up Banner)

Setting up a Roll Up Banner or Standee is easy. Follow the below-listed steps and refer to the images to setup your standee in seconds.

First time users might be a little confused when setting up their standee. This blog post guides you through the basic steps with illustrations on how to proceed with the installation. Also enlisted are some simple precautions for prolonging the life of your standee. 

Step 1 - Place the standee on a straight surface where there is enough space for both you and the standee. Never drop a standee on a hard surface. The corners are the most fragile parts of the standee and contain the spring. 

Setup Your Roll Up Banner or Standee with these easy steps


Step 2 - Unzip the cover near the edge and pull out the standee. Retain the cover for later use. Safe guarding a standee from dust goes a long way in enhancing its life. 

Simple steps to setup a standee


Step 3 - On one edges of the standee you will see a set of 3 aluminium pipes interconnected with an elastic string. This is the vertical support rod. Separate it from the standee. 

Simple steps to setup a roll up banner


Step 4 - Now place the standee upside down on a smooth surface and twist open the two feet at the bottom. Make these perpendicular to the direction of the standee. Now flip the standee and place it on these feet. 

Read on Mudraka How To Install a Standee 


Step 5 - Straighten out the 3 interconnected rods you separated from the standee in Step 3. Align the ends together to make it a single straight rod.

How to install a roll up banner - read on


Step 6 - Now insert the ends connected with string one into the other till it becomes one single rigid rod. The rod will now be 6 feet in length or as per the size of the standee you purchased. Take care not to hit a person or objects in your proximity. 

Easily setup a standee - follow the simple steps


Step 7 - One end of the rod has a plastic cap and the other end does not. Hold the rod vertical and insert the end without the plastic cap into the hole on the top surface of the standee as shown in the image. 

How to setup a standee


Step 8 - Inserting the rod can be a little difficult since the slot is meant to be tight. Rotate the rod if necessary as you push it into the slot. 

How to install a roll up banner


Step 9 - You must keep pushing the rod till it goes all the way into the channel and touches the bottom most surface of the standee. This is very important since the standee will not stay upright if the rod is not completely inserted and a partially inserted rod can also damage the standee frame and render it useless.

How to use a banner standee


Step 10 - Now put one foot each on the 2 feet of the standee to stabilise it, bend down and start pulling up the banner rolled into the standee. Please only hold onto the top channel attached to the banner. Holding or pulling the banner can stretch and damage it resulting in a shoddy appearance of the standee. Also use both your feet on both the feet of the standee. Stepping down on only one foot of the standee can damage it.

How to install and collapse a standee


Step 11 - As you straighten up, keep pulling the banner till it is 2 to 3 inches above the top end of the vertical support rod. Do not pull hard on the banner once it reaches the limit since this can damage the standee. Always use both hands. Take care not to let go of the top channel of the banner since a standee is very easily damaged if it rolls up with too fast with an impact. It must always be rolled up slowly with the banner aligned with the edges of the standee case. Never let go of the banner with a jerk. 

How to use and pack a standee


Step 12 - Now slowly let the banner roll down 2-3 inches while aligning the top channel on the banner with the slot in the plastic cap of the vertical support rod. If required twist the rod to align its slot with the top channel. Once the blade of the channel is fully inserted into the slot, you can let go of the standee. - Guide to standees and roll up banners


That's it. You're done. Step back and admire your standee. 

Follow the steps in reverse order to pack up your standee once you're done using it. 

Write to us at if you have any questions or concerns. 

Click here to go to our product page for standees if you want to order one!


Team Mudraka


Team Mudraka

Ohhhhh tha’s a great post, i read many blogs but it is a very healpful information. Thanks for sharing with us.

Team Mudraka

I would like to make standee for my upcoming seminar
Please guide how to place order with you.

Leave a comment

Please note: comments must be approved before they are published.

Left Continue shopping
Your Order

You have no items in your cart